Toyota Avalon (XX50): Radio Receiver

Components

COMPONENTS

ILLUSTRATION

ILLUSTRATION

Installation

INSTALLATION

PROCEDURE

1. PRECAUTION

(a) w/o Navigation System:

NOTICE:

• When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
  • A communication malfunction DTC may be stored.
  • The radio and display receiver assembly may not operate normally.

(b) w/ Navigation System:

NOTICE:

• When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
  • A communication malfunction DTC may be stored.
  • The radio and display receiver assembly or navigation ECU may not operate normally.
• After replacing the radio and display receiver assembly, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the navigation ECU.

2. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY

3. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 8 claws to install the No. 2 instrument panel register assembly as shown in the illustration.

Install in this Direction

4. INSTALL NO. 2 RADIO RECEIVER BRACKET

(a) Install the No. 2 radio receiver bracket with the 4 screws.

5. INSTALL NO. 1 RADIO RECEIVER BRACKET

(a) Install the No. 1 radio receiver bracket with the 4 screws.

6. INSTALL INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

Click here

7. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

(a) Connect each connector.

(b) Engage the 5 clips to temporarily install the radio and display receiver assembly with bracket as shown in the illustration.

Install in this Direction

(c) Install the radio and display receiver assembly with bracket with the 4 bolts.

8. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL

Click here

9. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Click here

10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

11. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY

Click here

12. INSTALL FRONT CONSOLE UPPER PANEL GARNISH

Click here

13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH

Click here

14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

Click here

Removal

REMOVAL

PROCEDURE

1. PRECAUTION

(a) w/o Navigation System:

NOTICE:

• When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
  • A communication malfunction DTC may be stored.
  • The radio and display receiver assembly may not operate normally.

(b) w/ Navigation System:

NOTICE:

• When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
  • A communication malfunction DTC may be stored.
  • The radio and display receiver assembly or navigation ECU may not operate normally.
• After replacing the radio and display receiver assembly, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the navigation ECU.

2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH

Click here

3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH

Click here

4. REMOVE FRONT CONSOLE UPPER PANEL GARNISH

Click here

5. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY

Click here

6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

7. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Click here

8. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL

Click here

9. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

(a) Remove the 4 bolts.

(b) Pull the radio and display receiver assembly with bracket toward the rear of the vehicle to disengage the 5 clips.

Remove in this Direction

(c) Disconnect each connector and remove the radio and display receiver assembly with bracket.

10. REMOVE INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

Click here

11. REMOVE NO. 1 RADIO RECEIVER BRACKET

(a) Remove the 4 screws and No. 1 radio receiver bracket.

12. REMOVE NO. 2 RADIO RECEIVER BRACKET

(a) Remove the 4 screws and No. 2 radio receiver bracket.

13. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Disengage the 8 claws and remove the No. 2 instrument panel register assembly as shown in the illustration.

Remove in this Direction

14. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY