Installation
INSTALLATION
PROCEDURE
1. INSTALL ACTIVE NOISE CONTROL MICROPHONE
HINT:
Use the same procedure for all active noise control microphones.
(a)
Engage the 2 claws to install the active noise control microphone to
the roof headlining holder cover as shown in the illustration.
 | Install in this Direction |
2. INSTALL ACTIVE NOISE CONTROL MICROPHONE WITH COVER
HINT:
Use the same procedure for all active noise control microphone with covers.
(a) Engage the 2 claws to install the active noise control microphone with cover as shown in the illustration.
|
| Install in this Direction |
(b) Connect the connector.
3. INSTALL ROOF HEADLINING ASSEMBLY
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during active noise control microphone
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
|
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
|
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE ROOF HEADLINING ASSEMBLY
Click here
2. REMOVE ACTIVE NOISE CONTROL MICROPHONE WITH COVER
HINT:
Use the same procedure for all active noise control microphone with covers.
| (a) Disconnect the connector. | |
(b) Disengage the 2 claws to remove the active noise control microphone with cover as shown in the illustration.
 |
Remove in this Direction |
3. REMOVE ACTIVE NOISE CONTROL MICROPHONE
HINT:
Use the same procedure for all active noise control microphones.
(a)
Disengage the 2 claws to remove the active noise control microphone
from the roof headlining holder cover as shown in the illustration.
|
|
Remove in this Direction |
