Installation
INSTALLATION
PROCEDURE
1. PRECAUTION
NOTICE:
- When replacing the radio and display receiver assembly or navigation
ECU, always replace it with a new one. If a radio and display receiver
assembly or navigation ECU which was installed to another vehicle is
used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the navigation ECU, if "New software is not compatible
with the system. Contact your dealer." is displayed on the
multi-display, update the software of the radio and display receiver
assembly.
2. INSTALL NAVIGATION ECU
3. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH ANTENNA CORD (w/ Manual (SOS) Switch)
4. INSTALL NO. 1 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Engage the guide and install the No. 1 telephone bracket with the 2 screws.
(b) w/ Manual (SOS) Switch:
(1) Engage the 3 guides and install the No. 1 telephone bracket with the 3 screws.
5. INSTALL NO. 2 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Engage the guide and install the No. 2 telephone bracket with the 2 screws.
(2) Engage the wiring harness clamp.
(b) w/ Manual (SOS) Switch:
(1) Engage the 3 guides and install the No. 2 telephone bracket with the 3 screws.
(2) Engage the wiring harness clamp.
(3) Engage the clamp.
6. INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY
Click here 
7. INSTALL NAVIGATION ECU WITH BRACKET
(a) w/o Manual (SOS) Switch:
(1) Connect each connector.
(2) Install the navigation ECU with bracket with the 2 nuts as shown in the illustration.
 |
Install in this Direction |
(3) Connect the connector.
(b) w/ Manual (SOS) Switch:
(1) Connect each connector.
(2) Install the navigation ECU with bracket with the 2 nuts as shown in the illustration.
|
|
Install in this Direction |
(3) Connect the 2 connectors.
8. INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
9. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here
10. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here
11. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
13. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
14. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Click here
15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
- When replacing the radio and display receiver assembly or navigation
ECU, always replace it with a new one. If a radio and display receiver
assembly or navigation ECU which was installed to another vehicle is
used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the navigation ECU, if "New software is not compatible
with the system. Contact your dealer." is displayed on the
multi-display, update the software of the radio and display receiver
assembly.
2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
4. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here
5. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
7. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
8. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here
9. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here
10. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
11. REMOVE NAVIGATION ECU WITH BRACKET
(a) w/o Manual (SOS) Switch:
| (1) Disconnect the connector. | |
(2) Remove the 2 nuts and pull the navigation ECU with bracket as shown in the illustration.
 |
Remove in this Direction |
(3) Disconnect each connector and remove the navigation ECU with bracket.
(b) w/ Manual (SOS) Switch:
| (1) Disconnect the 2 connectors. | |
(2) Remove the 2 nuts and pull the navigation ECU with bracket as shown in the illustration.
|
|
Remove in this Direction |
(3) Disconnect each connector and remove the navigation ECU with bracket.
12. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY
Click here
13. REMOVE NO. 2 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
| (1) Disengage the wiring harness clamp. | |
| (2) Remove the 2 screws and disengage the guide to remove the No. 2 telephone bracket. |
|
(b) w/ Manual (SOS) Switch:
| (2) Disengage the wiring harness clamp. | |
| (3) Remove the 3 screws and disengage the 3 guides to remove the No. 2 telephone bracket. |
|
14. REMOVE NO. 1 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
| (1) Remove the 2 screws and disengage the guide to remove the No. 1 telephone bracket. |
|
(b) w/ Manual (SOS) Switch:
| (1) Remove the 3 screws and disengage the 3 guides to remove the No. 1 telephone bracket. |
|
15. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH ANTENNA CORD (w/ Manual (SOS) Switch)
16. REMOVE NAVIGATION ECU
