Installation
INSTALLATION
PROCEDURE
1. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY
2. INSTALL NO. 2 AMPLIFIER BRACKET
(a) Install the No. 2 amplifier bracket with the 2 screws.
3. INSTALL NO. 1 AMPLIFIER BRACKET
(a) Engage the guide.
(b) Install the No. 1 amplifier bracket with the 2 screws.
4. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET
| (a) Turn back the front floor carpet assembly and front floor mat as shown in the illustration. |
|
(b)
Engage the 2 guides and temporarily install the stereo component
amplifier assembly with bracket as shown in the illustration.
 |
Install in this Direction (1) |
 |
Install in this Direction (2) |
(c) Install the stereo component amplifier assembly with bracket with the bolt.
| (d) Install the front floor carpet assembly and front floor mat to its original position as shown in the illustration. |
|
(e) Engage the clamp.
(f) Connect each connector.
5. INSTALL AUDIO AMPLIFIER COVER
(a) Install the audio amplifier cover with the 3 clips.
6. INSTALL FRONT SEAT ASSEMBLY LH
Click here 
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during stereo component amplifier assembly
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
Click here
2. REMOVE AUDIO AMPLIFIER COVER
| (a) Remove the 3 clips and audio amplifier cover. | |
3. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET
| (a) Disconnect each connector. | |
(b) Disengage the clamp.
|
(c) Turn back the front floor carpet assembly and front floor mat as shown in the illustration. |
|
(e) Disengage the 2 guides and remove the stereo component amplifier assembly with bracket as shown in the illustration.
 |
Remove in this Direction (1) |
 |
Remove in this Direction (2) |
4. REMOVE NO. 1 AMPLIFIER BRACKET
(b) Disengage the guide to remove the No. 1 amplifier bracket.
5. REMOVE NO. 2 AMPLIFIER BRACKET
| (a) Remove the 2 screws and No. 2 amplifier bracket. | |
6. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY
