Components
COMPONENTS
ILLUSTRATION
|
*1 | REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*2 | REAR DOOR OPENING TRIM WEATHERSTRIP RH |
|
*3 | ROOF SIDE INNER GARNISH LH |
*4 | ROOF SIDE INNER GARNISH RH |
|
*5 | ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*6 | ROOF SIDE RAIL GARNISH ASSEMBLY RH |
|
*7 | CLIP |
- | - |
|
● | Non-reusable part |
- | - |
ILLUSTRATION
|
*1 | PACKAGE TRAY TRIM PANEL ASSEMBLY |
*2 | REAR NO. 3 SPEAKER ASSEMBLY |
|
*3 | REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH |
*4 | REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH |
|
*5 | REAR SEAT SHOULDER BELT COVER |
- | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- | - |
ILLUSTRATION
|
*A | w/o Seat Heater System |
- | - |
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
|
*A | w/o Seat Heater System |
- | - |
|
*1 | LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 | NO. 1 UPPER BACK PANEL HOLE COVER |
|
*3 | ROOM PARTITION BOARD LH |
*4 | ROOM PARTITION BOARD RH |
|
*5 | SPEAKER ASSEMBLY WITH BRACKET |
- | - |
Inspection
INSPECTION
PROCEDURE
1. INSPECT REAR NO. 3 SPEAKER ASSEMBLY
(a) With the speaker installed, check that there is no looseness or other abnormalities.
(b) Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities.
| (c) Measure the resistance of the speaker. Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
1 (WF2-) - 2 (WF2+) |
Always | 4.2 to 6.4 Ω | |
3 (WF1-) - 4 (WF1+) |
Always | 4.2 to 6.4 Ω |
If the result is not as specified, replace the speaker. |
 |
|
*a | Component without harness connected
(Rear No. 3 Speaker Assembly) | | |
2. INSPECT SPEAKER ASSEMBLY WITH BRACKET
(a) With the speaker installed, check that there is no looseness or other abnormalities.
(b) Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities.
| (c) Measure the resistance of the speaker. Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
1 - 2 | Always |
2.8 to 3.8 Ω | If the result is not as specified, replace the speaker. |
 |
|
*a | Component without harness connected
(Speaker Assembly With Bracket) | | |
Installation
INSTALLATION
PROCEDURE
1. INSTALL SPEAKER ASSEMBLY WITH BRACKET
NOTICE:
Do not touch the speaker cone.
(a) for LH Side:
(1) Connect the connector.
| (2) Engage the guide and install the speaker assembly with bracket with the 2 bolts.
HINT: Install the bolts in the order shown in the illustration. |
|
(b) for RH Side:
| (1) Engage the guide and install the speaker assembly with bracket with the 2 bolts.
HINT: Install the bolts in the order shown in the illustration. |
|
(2) Connect the connector.
2. INSTALL NO. 1 UPPER BACK PANEL HOLE COVER
(a) Install the No. 1 upper back panel hole cover as shown in the illustration.
 |
Install in this Direction |
3. INSTALL ROOM PARTITION BOARD RH
Click here 
4. INSTALL ROOM PARTITION BOARD LH
Click here
5. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/o Seat Heater System)
Click here
6. INSTALL SPARE WHEEL COVER ASSEMBLY (w/o Seat Heater System)
Click here
7. INSTALL REAR NO. 3 SPEAKER ASSEMBLY
NOTICE:
Do not touch the speaker cone.
| (a) Engage the guide and install the rear No. 3 speaker assembly with the 4 bolts.
HINT: Install the bolts in the order shown in the illustration. |
|
(b) Connect the connector.
8. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
9. INSTALL REAR SEAT SHOULDER BELT COVER
Click here
10. INSTALL CENTER STOP LIGHT SET
Click here
11. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
12. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
13. INSTALL ROOF SIDE INNER GARNISH LH
Click here
14. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
15. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
16. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
17. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
18. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
19. INSTALL REAR SEAT ASSEMBLY
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during rear package tray speaker
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE REAR SEAT ASSEMBLY
Click here
2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
3. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
4. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
5. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
6. REMOVE ROOF SIDE INNER GARNISH LH
Click here
7. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
8. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
9. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE CENTER STOP LIGHT SET
Click here
11. REMOVE REAR SEAT SHOULDER BELT COVER
Click here
12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
13. REMOVE REAR NO. 3 SPEAKER ASSEMBLY
NOTICE:
Do not touch the speaker cone.
| (a) Disconnect the connector. | |
| (b) Remove the 4 bolts and disengage the guide to remove the rear No. 3 speaker assembly. |
|
14. REMOVE SPARE WHEEL COVER ASSEMBLY (w/o Seat Heater System)
Click here
15. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/o Seat Heater System)
Click here
16. REMOVE ROOM PARTITION BOARD LH
Click here
17. REMOVE ROOM PARTITION BOARD RH
Click here
18. REMOVE NO. 1 UPPER BACK PANEL HOLE COVER
(a) Remove the No. 1 upper back panel hole cover as shown in the illustration.
 |
Remove in this Direction |
19. REMOVE SPEAKER ASSEMBLY WITH BRACKET
NOTICE:
Do not touch the speaker cone.
(a) for LH Side:
| (1) Remove the 2 bolts and disengage the guide. | |
| (2) Disconnect the connector to remove the speaker assembly with bracket. |
|
(b) for RH Side:
| (1) Disconnect the connector. |
|
| (2) Remove the 2 bolts and disengage the guide to remove the speaker assembly with bracket. |
|
